UNICONE PLUS VS. UNICONE – IN VITRO CYCLIC FATIGUE STUDY AT DIFFERENT ENVIROMENTAL TEMPERATURES
Authors:
A. Jusku; P. Jirásek; A. Petřivalská; M. Rosa; J. Staněk; Ľ. Harvan
Authors‘ workplace:
Klinika zubního lékařství, Lékařská fakulta Univerzity Palackého a Fakultní nemocnice, Olomouc
Published in:
Česká stomatologie / Praktické zubní lékařství, ročník 120, 2020, 3, s. 88-93
Category:
Original articles
Overview
Introduction, aim: The issue of fracture of endodontic nickel-titanium instruments is quite extensive. It is an alloy that has the ability to change its internal structure. A great deal of effort is devoted to the development of an alloy with ideal properties. Instruments fracture occurs for two basic reasons. The first one is exceeding the limit of resistence of the instrument to cyclic fatigue and the other one is exceeding the limit of torsional load of the instrument. Most authors agree, that the main factor influencing instruments fracture is exceeding the limit of cyclic fatigue. The aim of this study was to evaluate the resistence to cyclic fatigue of the Unicone Plus in comparison with its predecessor, Unicone, under different enviromental conditions.
Methods: A total of forty (20 + 20) Unicone 6/025 and Unicone Plus 6/025 instruments (Medin, Czech republic) with identical tip diameter of 0.25 mm and constant taper of 0.06 were subjected to cyclic fatigue test at temperatures 20 °C ± 1 °C and 35 °C ± 1 °C. Special device was constructed for testing. This device uses the principle of using an artificial root canal made of stainless steel with a radius of the curvature of 5 mm, an angle of curvature of 60°. A thermostatic bath was added to the set-up. The liquid of the desired temperature was added to the container and maintained at that temperature throughout the test under the control of an infrared thermometer. Due to the fact that tested instruments are used in reciprocal movement, they were tested in Reciproc ALL mode. To evaluate cyclic fatigue of the instruments, the time was measured from the start of rotation of the instrument, until the fracture occured with an accuracy of whole seconds. The non-parametric Kruskal-Wallis test was used for statistical evaluation, followed by Mann-Whitney U-tests of multiple comparison and Bonferroni correction at the significance level of 5%.
Results: The obtained results from four groups were compared. Unicone instruments were statistically significantly less durable than Unicone Plus at both temperatures tested (p < 0.05). Higher enviromental temperature had statistically significant effect on lowering of cyclic fatigue resistence (p < 0.05).
Conclusion: Unicone Plus instruments are more resistant to cyclic loading than Unicone. In this case, greater durability is most likely associated with innovative manufacturing processes. Furthermore, the resistence of instruments to cyclic fatigue dereases with increasing ambient temperature.
Keywords:
cyclic fatigue – instrument fracture – reciprocation instruments – fracture resistence – NiTi alloy processing
Sources
1. Thompson SA. An overview of nickel-titanium alloys used in dentistry. Int Endod J. 2000; 33(4): 297–310.
2. Zhou H, Peng B, Zheng Y-F. An overview of the mechanical properties of nickel-titanium endodontic instruments. Endod Topics. 2013; 29(1): 42–54.
3. Cheung GSP, Darvell BW. Fatigue testing of a NiTi rotary instrument. Part 2: Fractographic analysis. Int Endod J. 2007; 40(8): 619–625.
4. Parashos P, Gordon I, Messer HH. Factors influencing defects of rotary nickel-titanium endodontic instruments after clinical use. J Endod. 2004; 30(10): 722–725.
5. Shen Y, Cheung GSP, Peng B, Haapasalo M. Defects in nickel-titanium instruments after clinical use. Part 2: Fractographic analysis of fractured surface in a cohort study. J Endod. 2009; 35(1): 133–136.
6. Sattapan B, Nervo GJ, Palamara JE, Messer HH. Defects in rotary nickel-titanium files after clinical use. J Endod. 2000; 26(3): 161–165.
7. Zupanc J, Vahdat-Pajouh N, Schäfer E. New thermomechanically treated NiTi alloys – a review. Int Endod J. 2018; 51(10): 1088–1103.
8. Plotino G, Grande NM, Testarelli L, Gambarini G, Castagnola R, Rossetti A,Özyürek T, Cordaro M, Fortunato L. Cyclic fatigue of reciproc and reciproc blue nickel-titanium reciprocating files at different environmental temperatures. J Endod. 2018; 44(10): 1549–1552.
9. Plotino G, Ahmed HMA, Grande NM, Cohen S, Bukiet F. Current assessment of reciprocation in endodontic preparation: A comprehensive review – Part II: Properties and effectiveness. J Endod. 2015; 41(12): 1939–1950.
10. Yared G. Canal preparation using only one Ni-Ti rotary instrument: Preliminary observations. Int Endod J. 2008; 41(4): 339–344.
11. Pedullà E, Grande NM, Plotino G, Gambarini G, Rapisarda E. Influence of continuous or reciprocating motion on cyclic fatigue resistance of 4 different nickel-titanium rotary instruments. J Endod. 2013; 39(2): 258–261.
12. De-Deus G, Moreira EJL, Lopes HP, Elias CN. Extended cyclic fatigue life of F2 ProTaper instruments used in reciprocating movement. Int Endod J. 2010; 43(12): 1063–1068.
13. Castelló-Escrivá R, Alegre-Domingo T,Faus-Matoses V, Román-Richon S, Faus-Llácer VJ. In vitro comparison of cyclic fatigue resistance of ProTaper, WaveOne, and twisted files. J Endod. 2012; 38(11): 1521–1524.
14. Melo MCC, Pereira ESJ, Viana ACD, Fonseca AMA, Buono VTL, Bahia MGA. Dimensional characterization and mechanical behaviour of K3 rotary instruments. Int Endod J. 2008; 41(4): 329–338.
15. Bahia MGA, Lopes Buono VT. Decrease in the fatigue resistance of nickel-titanium rotary instruments after clinical use in curved root canals. Oral Surg Oral Med Oral Pathol Oral Radiol Endod. 2005; 100(2): 249–255.
16. Plotino G, Grande NM, Testarelli L, Gambarini G. Cyclic fatigue of Reciproc and WaveOne reciprocating instruments. Int Endod J. 2012; 45(7): 614–618.
17. Grande NM, Plotino G, Pecci R, Bedini R, Malagnino VA, Somma F. Cyclic fatigue resistance and three-dimensional analysis of instruments from two nickel-titanium rotary systems. Int Endod J. 2006; 39(10): 755–763.
18. Testarelli L, Grande N, Plotino G,Lendini M, Pongione G, Paolis G De, Rizzo F, Milana V, Gambarini G. Cyclic fatigue of different nickel-titanium rotary instruments: A comparative study. Open Dent J. 2009; 2009(3): 55–58. doi: 10.2174/1874210600903010055.
19. Wu SK, Lin HC, Chou TS. A study of electrical resistivity, internal friction and shear modulus on an aged Ti49Ni51 alloy. Acta Metall Mater. 1990; 38(1): 95–102.
20. Hou XM, Yahata Y, Hayashi Y, Ebihara A, Hanawa T, Suda H. Phase transformation behaviour and bending property of twisted nickel-titanium endodontic instruments. Int Endod J. 2011; 44(3): 253–258.
21. Gambarini G, Gerosa R, De Luca M, Garala M, Testarelli L. Mechanical properties of a new and improved nickel-titanium alloy for endodontic use: an evaluation of file flexibility. Oral Surg Oral Med Oral Pathol Oral Radiol Endod. 2008; 105(6): 798–800.
22. Larsen CM, Watanabe I, Glickman GN, He J. Cyclic fatigue analysis of a new generation of nickel titanium rotary instruments. J Endod. 2009; 35(3): 401–403.
23. Bhagabati N, Yadav S, Talwar S. An in vitro cyclic fatigue analysis of different endodontic nickel-titanium rotary instruments. J Endod. 2012; 38(4): 515–518.
24. Daneshmand S, Kahrizi EF, Abedi E, Mir Abdolhosseini M. Influence of machining parameters on electro discharge machining of NiTi shape memory alloys. Int J Electrochem Sci. 2013; 8(3): 3096–3104.
25. Singh S, Maheshwari S, Pandey PC.Some investigations into the electric discharge machining of hardened tool steel using different electrode materials. J Mater Process Technol. 2004; 149(1–3): 272–277.
26. Pirani C, Iacono F, Generali L, Sassatelli P, Nucci C, Lusvarghi L, Gandolfi MG, Prati C. HyFlex EDM: Superficial features, metallurgical analysis and fatigue resistance of innovative electro discharge machined NiTi rotary instruments. Int Endod J. 2016; 49(5): 483–493.
27. Pedullà E, Lo Savio F, Boninelli S, Plotino G, Grande NM, La Rosa G, Rapisarda E. Torsional and cyclic fatigue resistance of a new nickel-titanium instrument manufactured by electrical discharge machining. J Endod. 2016; 42(1): 156–159.
28. Hassel AW. Surface treatment of NiTi for medical applications. Minim Invasive Ther Allied Technol. 2004; 13(4): 240–247.
29. Condorelli GG, Bonaccorso A, Smecca E, Schäfer E, Cantatore G, Tripi TR. Improvement of the fatigue resistance of NiTi endodontic files by surface and bulk modifications. Int Endod J. 2010; 43(10): 866–873.
30. Anderson ME, Price JWH, Parashos P. Fracture resistance of electropolished rotary nickel-titanium endodontic instruments. J Endod. 2007; 33(10): 1212–1216.
31. Zinelis S, Darabara M, Takase T, Ogane K, Papadimitriou GD. The effect of thermal treatment on the resistance of nickel-titanium rotary files in cyclic fatigue. Oral Surg Oral Med Oral Pathol Oral Radiol Endod. 2007; 103(6): 843–847.
32. Otsuka K, Ren X. Physical metallurgy of Ti-Ni-based shape memory alloys. Prog Mater Sci. 2005; 50(5): 511–678.
33. De Hemptinne F, Slaus G, Vandendael M, Jacquet W, De Moor RJ, Bottenberg P. In vivo intracanal temperature evolution during endodontic treatment after the injection of room temperature or preheated sodium hypochlorite. J Endod. 2015; 41(7): 1112–1115.
34. Plotino G, Grande NM, Mercadé Bellido M, Testarelli L, Gambarini G. Influence of temperature on cyclic fatigue resistance of ProTaper Gold and ProTaper Universal Rotary Files. J Endod. 2017; 43(2): 200–202.
35. Grande NM, Plotino G, Silla E, Pedullà E, DeDeus G, Gambarini G, Somma F. Environmental temperature drastically affects flexural fatigue resistance of nickel-titanium rotary files. J Endod. 2017; 43(7): 1157–1160.
Labels
Maxillofacial surgery Orthodontics Dental medicineArticle was published in
Czech Dental Journal
2020 Issue 3
Most read in this issue
- THE MARGINAL AND INTERNAL FIT OF COCR ALLOY SINGLE CROWNS WITH PREPARATION DESIGNS INCLUDING AUXILIARY FEATURES; CAD/CAM VERSUS CONVENTIONAL TECHNIQUE
- EFFECT OF LOW, MEDIUM AND HIGH MOLECULAR WEIGHT HYALURONIC ACID ON HUMAN DENTAL PULP STEM CELLS
- UNICONE PLUS VS. UNICONE – IN VITRO CYCLIC FATIGUE STUDY AT DIFFERENT ENVIROMENTAL TEMPERATURES
- Vzpomínka na profesora Eduarda Nessela